AT-80PD
DIGITAL ELECTRIC FLAT SCREEN PRINTER
For screen-printing substrates in Flat Sheet/Board form made of non-deforming materials. Ex: Stickers, Decals, Posters, Nameplates, Sign Boards, Printed Circuit Boards, etc.
A. German S.E.W. Motor powers screen up / down position and drive motor for squeegee / flood travel. Provides high cycle speed with smooth mechanical movements, low noise and accuracy.
B. Printing table surface is CNC precision milled and manufactured from high quality anodized aluminum to achieve close tolerance planarity. Honeycomb construction for rigidity, while offering powerful, heat-dissipating turbine vacuum. Suction force is adjustable for optimum substrate control and printing requirements. NOTE: Model AT-70PD can be equipped with a T-groove slotted table designed for an easy addition of fixtures and toolings.
C. Travel of squeegee / flood on guided precision sealed linear motion bearings, reinforced tooth belt, timing belt wheel for high rigidity and ultra-smooth high print speed transport cycles without backlash. This ultra-smooth gliding of the squeegee / flood assembly enables step-less speed change for higher production speed, smooth operation, consistent / uniform printing deposit control, less maintenance and fast operation.
D. Squeegee / flood high-park capability facilitates faster setup and changeover.
E. Pneumatic frame locking with check valves / airlock and four-sided frame holding assembly ensures rigidity and high stability.
F. Patented mechanical print head lift guided on precision sealed linear motion bearings allows stable, vibration-free movement in up/down positions.
G. Squeegee and flood printing parameter settings for speed, pressure, and stroke travel distance is independently controlled by single action from the touch screen.
H. Includes pneumatic squeegee / flood pressure equalizer control system. Fully automatic and regulated by a constant pressure control system equalized with pivot point balance for angled substrate along with snowplow skew feature for irregular print surfaces.
I. Stable pneumatic cylinders are encased around solid cast to allow consistent pressurization of squeegee and flood. After initial setup pressure regulator can be increased and decreased on the fly. For most applications suitable pressure is 3-4 bars and the squeegee and flood both have pressure gauge to measure incremental setting amount.
J. Touch screen control of peel-off action to assist release of ink and mesh from substrate synchronized with the print stroke in the auto-mode of operation.
K. Peel-off height lifting point adjustable by low speed cylinder depending on print stroke with speed adjustment valve and mechanical adjustment to set peel-off height. Flood coat sequence is carried out with the frame in the horizontal position allowing a no peel flood function. This benefit offers more uniform control and evenness of ink layer over length and width of image area.
L. Touch screen control of off-contact height between substrate and screen. Numerical value can be set up to accommodate substrate thickness 0 – 120 mm (0 – 4.7”).
M. Print table X / Y movements via precision scaled micrometer control(s) for fine registration. Play-free registration without backlash.
N. Choice of six print functions from touch screen: flooding before the print stroke, flooding after the print stroke, higher cycle speed-flood while screen lifts to full up position, double squeegee printing mode with use of two squeegees mounted allowing printing in both directions and screen lift up to print position, twice printing mode (flood while screen lowers and the last flood when screen is in up position) and double squeegee mode with use of two squeegees to perform left print direction while right squeegee is idle and right print direction while left squeegee is idle. Includes no flood setting and print head lift for ease of sq / fl load and unload without removing for fast setup.
O. Touch screen input of printing standby height: AT-60PD / PPD 150-260mm, AT-70PD 150-270mm. This is the distance that the screen lifts up after the squeegee and flood sequence. Numeric value can be preset to stop the screen in a lower position for increase cycle speed.
P. Squeegee / flood assembly is synchronized and changeover is pneumatically operated for smoother transition. Adjustable height controls, angle settings 0-30°, leveling and skew feature. Provides uniform ink deposits across the entire print area.
Q. Touch screen input variable and independent for print and flood stroke speed and length setting to image size. Numerical input of right print stroke start point AT-60PD 0-300mm, AT-70PD 0-340mm, and left stop point AT-60PD 400-700mm, AT-70PD 390-780mm.
R. Touch screen preset for printing position settings. Printing offset distance (5-50 mm) protects squeegee edge and mesh from wear by precisely lowering the squeegee past the leading edge of substrate. Premature wear or damage of squeegee and mesh can occur when squeegee moves across sharp edges of substrate when in direct contact.
S. Print operating cycles: Manual settings for setup procedure, setting for foot pedal control in single cycle and fully automatic control with dwell timer range of time selectable from 0.2-60 seconds for substrate loading and off-loading.
T. Productivity preset in numerical values for throughput can be changed anytime. Enter production quantity according to run length and during the run screen will indicate current yield until preset number of prints are achieved.
U. Frame loading and unloading from the front of the machine to facilitate fast setup and changeovers. Frame holding rails can be unlocked from touch screen and easily adjusted to the size of the frame.
V. Control system for compressed air supply is an oil free FRL unit to prevent oil mist pollution, applicable in clean room environment.
W. Equipped with powerful turbine vacuum control to prevent movement of the substrate.
X. Emergency press plate positioned in front of print table in case substrate alignment is not in the correct position. Operator can press the plate and printing head slowly lifts up to the full upright home position allowing operator the chance to register correctly final substrate alignment. Reduces spoilage and yields more printed product.
Y. Front safety bar location on the print head, compliant with OSHA safety regulations.
Z. Includes 3 squeegee holders and 3 flood coaters, sq. / fl clamps, pedal switch control, toolbox, tools and door key.
Specification | AT-80PD Metric | AT-80PD US Standard Units |
Max. O/D frame size (DxW) | 900mm x 1100mm | 35⅜" x 43¼" |
Working table size (DxW) | 700mm x 900mm | 27½" x 35⅜" |
Max. print area(DxW) | 600mm x 800mm | 23⅝" x 31⅜" |
Substrate thickness | 0-120mm | 0-4¾" |
Capacity(P/H,full speed full stroke) | 720 | 720 |
Power source | 3∮,220V/380V,50/60Hz | 3∮,220V/380V,50/60Hz |
Table adjustment (X,Y) | ±10mm,±10mm | ±⅜", ±⅜ |
Air source | 6.3-7.7 kg/cm² | 90 - 110psi |
Air consumption(I GI/cycle) | 1.65 L/cycle | 0.43 gal/cycle |
Dimension(WxDxH) | 150cm x 130cm x 170cm | 59" x 51¼" x 67" |
Weight | 805 kg | 1775 lbs |
SCREEN FRAME HEIGHT: For the convenience of our customers, ATMA prepares all machines sold through RH Solutions to accept roller, diamond chase, and stretch and glue frames with heights 28mm - 52mm (1.1" - 2").
For screen-printing substrates in Flat Sheet/Board form made of non-deforming materials. Ex: Stickers, Decals, Posters, Nameplates, Sign Boards, Printed Circuit Boards, etc.
Get A Quote
Looking for customized printing solutions? I invite you to fill out our Quote form to receive a tailored estimate that meets your specific requirements. Once you submit the form, I'll get back to you quickly to ensure we kickstart your project without delay!